originalsidebar2

 


Bacardi Cup
March 6 - 11, 2017
Miami, Florida

2017 Eastern Hemisphere Championship
June 1 - 4, 2017
Viareggio, Italy


2017 Western Hemisphere Championship
June 13 - 18, 2017
Cleveland, Ohio USA


Newest Star Number

8522


Star Class


Twitter


Facebook

Star Sailors League

 

     

Technical Articles

This Article Last Updated: Oct 14th, 2010 - 15:13:49 

Preparing Your Mast
By Mark Reynolds
Apr 16, 2003, 15:07

Email this article
 Printer friendly page
Before you step your rig next time, take a minute to check a few things out.You should look it over to help prevent any potential problems and there area few adjustments to check. You don't need a failure that may put you out of a race this season.

A few millimeters can be all there is between having your mast standing or letting the wind and gravity bring it right back down. Your mast can be slightly bent from last season and the spreaders and intermediates can have moved since the last time they were checked.

Tuning
Today's new masts come pretty ready to go. The mast manufactures do a good job of presetting the spreaders and the intermediates. A few days of goodpressure can seat things a bit so even a new mast should be rechecked. If you have a season or two on your mast it's way past time to check your settings.

I check mine quite a few times a year. Check to make sure that your mast is straight. Small adjustments are easy, particularly at the top where the welding has made the mast not asresilient. If you are careful you can straighten a mast that's been very bent. Before the 2000 Olympic Trails we rolled to windward and dipped the pole in the drink for a few seconds. As soon as it hit Magnus pushed the inboard end up the mast. Although the mast didn't break, it was pretty bent up. We were able to straighten bends that were both sideways and fore and aft.

Assuming that your intermediates are at the spreader tips, they need to be adjusted before attaching them to the spreaders. Pull the upper shroud down along the front of the mast and mark the inside bearing point on the mast. If you have a Spartech make sure to leave the small spacer in. You can put a phillips screwdriver through it to hold it in place and make a mark inline with the lower edge. Measure down from this point 2 15/16" (75mm) and make another mark. Now pull the intermediates down and adjust so that theinside bearing point is in line with this mark. Make sure you tighten thelocking nut.

After installing the spreaders tie some twine or shock cord tightly between the tips (right around the shrouds) and measure to the back of the mast checking the sweep of the spreaders. This normally comes at 5" and this works fine. At this point I also make sure that the line from tip to tip is perpendicular to the side of the mast butt plug. This can be checked byusing a level or you can line up a batten on the butt plug and check to see if it's in line with the twine between the spreader tips. If you haven't checked this for awhile it will most likely need a little adjusting.

Maintenance
Check your mast head sheave and halyard lock. They normally don't have problems but make sure that the pin that holds them in is secure. The lower pin that holds the halyard lock also holds the upper shrouds. This pin broke on Peter Bomby at this years Springs.

Take a very close look at the main halyard at the shackle and at the ball to make sure there are no broken wires. This should be replaced at least every few years.You should take off the jib box and check all of the screws inside and makesure that they are tight. Check the half sheave that the jib halyard runsaround. If you haven't kept the jib halyard waxed it will wear out quickly(don't forget to wax it!).

Before reinstalling check all the screw holes. Last year before the trials I found a crack from the top screw hole into the cutout. It was also starting to crack from the hole toward the side aswell. No question that it would have broken soon. Look around the spreader bracket and make sure that it's still tightlyriveted to the mast. If not, you can re-rivet it using stainless rivets.

Make sure when riveting anything to your mast to use something to insulate it, I use Alumilastic. If you have a collar around the mast as was used on many Folli's make sure that there is still a piece of plastic under it to insulate it from the aluminum mast. I've seen quite a few masts break off at this point.

Wipe the wires off with some MEK or acetone. It's a good idea to replace the rod rigging occasionally. I've seen wires break within 1 year and have seen them last for many years. The intermediates and headstays seem to break the most, and fortunately neither usually cause a broken mast. The lower diagonal shrouds and the outer lower cap shroud are more critical.

Check the shock cord that's tied from backstay to backstay near the spreaders. This should still have some stretch left in it and be about 6'long. If it's too long the leeward backstay can get caught around the spreader tip on a jibe.

I've been putting Starbright on my mast to keep it from getting pitted and spraying some McLube in the sail slot to make the sail move up and down a little easier. With the Spartech masts make sure to tape your spreader tips before standing the rig for two reasons. The bolts have been known to back out and they are also a bit sharp which has ripped many mains at starts and mark roundings.



Top of Page


footer.shtml
ISCYRA Central Office
2812 Canon Street
San Diego, California 92106 USA
Phone: +1 619 222 0252
Fax: +1 619 222 0528
SKYPE: star.class.office
office@starclass.org

Star Class

Results - Calendar - Classified Ads - History
Districts & Fleets - Rules - About - Online Store